Loading...
> >

Question about GYN-01 for Genesis 8 Female

the_assassinthe_assassin Posts: 73
in The Commons

I'm considering getting GYN-01 for Genesis 8 Female(s) | Daz 3D.  Of all davyabbo's cyborgs, I think it has the best body for my needs.  But I'm not keen on the human face/robot jaw combo it has.  Does anyone know if its possible to turn off or remove the robot jaw so that the whole face is human-looking? 

 

Comments

  • Matt_CastleMatt_Castle Posts: 2,654

    It is not. Unfortunately, high definition morphs are not editable by end users.

  • DaventakiDaventaki Posts: 1,624
    edited March 2022

    It looks like you can.  I dont know if you have the Daz Deals addon for your browser, but I looked at the gallery images and this one has a human face also this one.

    Post edited by Daventaki on
  • richardandtracyrichardandtracy Posts: 5,890
    Even if it is not, you should be able to dial the Gyn-01 head morph to zero, and dial up another to 100%.
  • HoMartHoMart Posts: 480
    edited March 2022

    There is no head morph, only a "GYN-01 !Apply Full Morph" - see attached screenshot.

    The images mentioned by @Daventaki are made with the GYN-01 geoshell materials without the bodymorph.

     

    Screenshot 2022-03-27 113357.jpg
    645 x 181 - 22K
    Post edited by HoMart on
  • the_assassinthe_assassin Posts: 73

    Ah, shame.  Thanks all.

  • hacsarthacsart Posts: 2,027

    I think  that you could accomplish this by editing the applicable Geoshell texture and opacity maps.. I've done that with sucess with other geoshells

  • richardandtracyrichardandtracy Posts: 5,890

    HoMart said:

    There is no head morph, only a "GYN-01 !Apply Full Morph" - see attached screenshot.

    The images mentioned by @Daventaki are made with the GYN-01 geoshell materials without the bodymorph.

     

    I don't have the model so I am talking from a position of little specific knowledge. The place where I would expect it is in the 'Shaping' tab (usually grouped with the Parameters & Material Tabs), with a slider that goes from 0-100%. If you look there you will see most G8F characters are applied as a 100% character body morph and a 100% character head morph, and it's rare for the character to only have a single Combined Head & Body morph slider. It was my hope that the same may be the case with this character.  

    Regards,

    Richard

  • FSMCDesignsFSMCDesigns Posts: 12,775

    richardandtracy said:

    HoMart said:

    There is no head morph, only a "GYN-01 !Apply Full Morph" - see attached screenshot.

    The images mentioned by @Daventaki are made with the GYN-01 geoshell materials without the bodymorph.

     

    I don't have the model so I am talking from a position of little specific knowledge. The place where I would expect it is in the 'Shaping' tab (usually grouped with the Parameters & Material Tabs), with a slider that goes from 0-100%. If you look there you will see most G8F characters are applied as a 100% character body morph and a 100% character head morph, and it's rare for the character to only have a single Combined Head & Body morph slider. It was my hope that the same may be the case with this character.  

    Regards,

    Richard

    Actully not that rare, Several asian characters in the store are single full figure morphs as well HH's Ronan and most characters from Rawart unfortunately.. I found the X-splitter product does a good job creating seperate morphs

Sign In or Register to comment.