Loading...
> >

Huge problem to get rid of much noise, even on full render cycle

launoklaunok Posts: 793
edited April 22 in Daz Studio Discussion

I am trying to get rid of heavy noise, even on light areas.  Normally dark areas shows noise more but not on my scene.

I even tried this denoise filtering to switch parts on:

- Firefly Filter Enable (ON)

- Post Denoiser Enable (ON)

- Post Denoiser Available (ON)

Post Denoiser Start Iteration: 8

It don't work at all.  After 2 hours render the noise is still much visible.

Attached cutout of image after full render time!

I have no idea why it's like this.  Are there other ways to make the noise less?

 

Any help is much appreciated.

 

Laura

 

 

APOCALYPTIC OFFICE 2 1.jpg
586 x 586 - 114K
Post edited by launok on

Comments

  • PerttiAPerttiA Posts: 10,024

    Which GPU, how much VRAM it has and how much RAM does your computer have?

  • Richard HaseltineRichard Haseltine Posts: 100,747

    and which GPU driver do you have?

    Check the log (View>Troubleshooting>View Log File) for messages relating to your render.

  • launoklaunok Posts: 793
    edited April 22

    PerttiA said:

    Which GPU, how much VRAM

    it has and how much RAM does your computer have?

     

    I am not good with these.  I checked on Taskbar.  Someone told me to look it up there.

    I have 16 GB ram memory

    GPU 0 shows 7,9 mem = (Intel(R) UHD Graphics 620)

    GPU 1 shows 9,9 mem = (Nvidia GeForce MX130)

    VRAM, where is it showing?

     

    Post edited by launok on
  • launoklaunok Posts: 793
    edited April 22

    Richard Haseltine said:

    and which GPU driver do you have?

    Check the log (View>Troubleshooting>View Log File) for messages relating to your render.

     

    Will check it out this evening with a friend who knows more than myself.  

    GPU 0 (Intel(R) UHD Graphics 620)

    GPU 1 (Nvidia GeForce MX130)

     

    Post edited by launok on
  • PerttiAPerttiA Posts: 10,024

    It looks like your MX130 has either 2GB's or 4GB's of VRAM (memory) and neither is enough for rendering Iray.
    The Intel UHD graphics is not supported for Iray.

    Is this a laptop or desktop computer?

  • launoklaunok Posts: 793
    edited April 22

    PerttiA said:

    It looks like your MX130 has either 2GB's or 4GB's of VRAM (memory) and neither is enough for rendering Iray.
    The Intel UHD graphics is not supported for Iray.

    Is this a laptop or desktop computer?

     

    It's a HP Laptop Corei7, got it in 2021 I think.

     

    Peter, my friend, suggested I make spotrenders of parts that has much noise on changing settings and do postwork in Affinity Photo.

    The progressive rendering was on:

    Max samples = 5000

    Max time = 7200    Why it stopped exactly after 2 hrs. 

    I need to higher this.  I have never used this before, in fact don't know much about render settings.

    I put as test it to 8000 for max samples and 10000 for max time.  Spotrender now after 40 minutes start to work a bit with less noise but still busy.

     

     

     

    Post edited by launok on
  • PerttiAPerttiA Posts: 10,024

    Disable Rendering Quality and set Max samples and Max time to something like 50000.

    Your computer cannot render Iray on GPU, so you are rendering on CPU, which is glacially slow (hours, many of them)
    When I had an 4GB Nvidia card, I used to render over night.

Sign In or Register to comment.